Water intake and transfer
Horizontal and vertical pump units for moving water between reservoirs, treatment stages and distribution zones.
- municipal facilities
- process water
Selection · assembly · testing
Pump units and packaged pump stations
We engineer and manufacture pump packages for water supply, pressure boosting, irrigation and industrial processes. Each solution combines the pump, motor, baseplate, pipework and valves into an installation-ready system.
Packaged stationsHydraulic testingPump service
For utilities, agriculture, industrial customers, OEM partners and system integrators in international markets.
From duty point to finished pump package — pump selection, unit layout, pipework, alignment, testing and preparation for installation.
Our approach
Not an isolated pump, but one coordinated hydraulic system
A pump must match the required flow, head and liquid properties. The motor, baseplate, manifolds, valves and installation conditions must work together, so our scope is the complete package rather than a single component.
01Pump unitHydraulic end, motor, coupling, guard and common baseplate
02Pipework and valvesManifolds, isolation and check valves, gauges and connections
03Assembly and testingAlignment, leak checks, performance verification and installation readiness
Outcome A packaged pump system prepared for integration at the customer site.
Applications
Pump solutions selected for the actual duty point
We consider flow, head, liquid properties, duty cycle, redundancy, installation conditions and maintenance requirements.
Pressure boosting
Compact multi-pump stations with manifolds, valves and duty/standby pump arrangements.
- buildings and facilities
- local networks
Irrigation
Pump packages for open water sources, storage reservoirs, greenhouses and field irrigation systems.
- agricultural operations
- greenhouse facilities
Industrial processes
Circulation, cooling, washing and transfer of process liquids in industrial infrastructure.
- continuous duty
- standby units
At the site
A pump station as part of the infrastructure
We consider pipe routing, access to valves, coupling and bearing maintenance, drainage and the ability to replace one unit without dismantling the complete station.
Discuss installation conditionsPump equipment
From a single pump unit to a packaged station
We select the pump type, motor, wetted materials and package layout according to the system parameters and operating environment.
01
Horizontal centrifugal pump units
Pump and motor on a common baseplate with coupling, guard, alignment and prepared process connections.
02
Vertical multistage pumps
Compact units for water supply, pressure boosting and applications requiring high head with a small installation footprint.
03
Multi-pump booster stations
Two or more pumps on a common frame with manifolds, isolation valves, gauges and the required redundancy.
04
Spare parts and service
Inspection and replacement of impellers, shafts, seals and bearings, followed by realignment and unit checks.
Single pump unit
Pump and motor on a common baseplate
We package a horizontal centrifugal pump with its drive motor, coupling, guard and rigid baseplate. Fasteners and unit alignment are checked before delivery.
Packaged station
Shipment readiness is confirmed by inspection
After assembly, we verify completeness, valve positions, instrument readings and connection condition. The results and package configuration are recorded on the acceptance sheet.
In-house manufacturing
Pump assembly, alignment and testing
We assemble pump units on common frames, fabricate the package pipework, verify connections and check operating parameters before delivery.
Pump unit assembly
Mounting the pump and motor on a baseplate with the coupling, supports, guards and process connections.
Precision alignment
Checking shaft alignment and adjusting unit position for stable operation and service life.
Package pipework
Manifolds, piping, valves, pressure gauges and auxiliary components on a common support frame.
Testing and service
Leak and parameter checks, hydraulic-end inspection and preparation for shipment.
Before shipment
We test the complete station on a test loop
The assembled package is connected to the test circuit to check joint integrity, pressure-gauge readings and final completeness. The results are recorded on an inspection sheet before delivery.
- pipework integrity
- operating readings
- final completeness
Pump service
Every repair starts with inspection
We disassemble the pump, clean and inspect the hydraulic end, measure critical fits and identify the parts that require restoration or replacement.
- shaft and impeller
- seals and bearings
- reassembly and alignment
Complete cycle
From duty point to a finished pump package
- 01
Duty requirements
We define flow, head, liquid, temperature, duty cycle, installation conditions and available power.
- 02
Selection and layout
We select the pump size, motor, materials, redundancy, baseplate, manifolds and valves.
- 03
Assembly
We mount the units, fabricate the pipework, verify connections and perform precision alignment.
- 04
Testing
We check leaks and operating parameters, then prepare the package for shipment and installation.
International cooperation
A pump package partner for OEMs and system integrators
We work from duty parameters or customer documentation. The scope may cover a pump unit, skid module or complete station prepared for site integration.
Discuss cooperation01Pump selectionHydraulic-end and motor selection for the required duty point and liquid
02Custom pump packagesPump units and multi-pump stations configured for project requirements
03Integration-ready supplyPipework, valves and connections prepared for site installation
04Testing and serviceParameter verification, pump inspection and technical support
To get started
What to send for an initial project review
If some information is not yet available, describe the task in your own words. The list helps identify the data required for the next step.
- 01Required flow and head at the duty point
- 02Liquid, temperature and any suspended solids
- 03Duty cycle, redundancy and available power supply
- 04Installation conditions and dimensional limits
- 05Connection diameters, pressure and standards
- 06Available drawings or photos of the existing system
Contact
Do you need a pump unit or packaged station?
Send the required flow, head, liquid description, installation conditions, drawings or photos of the existing system. We will confirm the data and propose a suitable equipment configuration.
Email for technical enquiries[email protected]Please include the product type or project name in the subject lineSend project requirements